Interactive Tool

Automotive Solar Heat Gain Calculator (EV-Optimized)

Estimate cabin temperature reduction, AC compressor power saving, and EV range extension from ATO solar heat control glazing — across compact, mid-size, and premium EV segments. Methodology derived from peer-reviewed thermal models, transparent on inputs and limitations.

Engineering reference for vehicle thermal architects, energy-balance modellers, and procurement teams scoping solar heat control glazing. Numbers reflect indicative platform archetypes; per-OEM runs require platform-specific dossiers.

How solar heat gain affects EV range

Battery electric vehicles are uniquely exposed to climate load. Without an idling engine to draw on, every kilowatt of compressor power comes directly out of the traction battery. On a hot day with sustained solar load, air-conditioning becomes the largest non-traction energy sink — often 10 to 20 percent of total energy use over a representative WLTP cycle at 35 degrees Celsius ambient.

Solar heat gain is the upstream driver. Incident solar radiation hitting the glazing surface partly transmits into the cabin and partly absorbs into the glass, with the absorbed fraction reradiated inward. The cabin temperature rises, the compressor cycles harder, the battery drains faster, the range falls. The cleanest place to intervene is at the glazing: reject the near-infrared (NIR) portion of solar radiation — which is heat, not vision — before it ever enters the cabin.

What this calculator computes

Calculation Model 887 takes three user inputs (vehicle segment, ambient conditions implicit in the segment archetype, and currency) and returns four engineering outputs:

  • Cabin temperature reduction at reference solar load (degrees Celsius)
  • AC compressor power saving at equivalent comfort setpoint (percent)
  • Range extension under hot-climate driving (kilometres per charge)
  • Annual energy cost saving at typical residential electricity tariffs (five currencies)

The underlying logic is deterministic: SHGC delta drives heat-gain reduction, which drives a proportional reduction in AC power demand, which converts to battery energy saved per kilometre, which extends range and reduces cost. No Monte Carlo, no opaque coefficients. Inputs and assumptions are documented in the methodology section below.

The calculator

Adjust the segment selector to model your platform. The tool runs entirely client-side; no data leaves your browser.

Automotive solar-heat chain

Transparent physics chain per window: optics → solar heat → cooling load → HVAC energy → fuel & CO₂ → €. Windscreen and front-side Kriya SHGC are disabled unless a VLT ≥ 70 % is entered (UN R43 Annex 21 §4.1.1 + §4.2.1.1). Reference glazing defaults to the measured clear-laminate 0.89 (no-ATO point of the 2018 PVB pilot series).

Vehicle & drivetrain
Conditions

Per-window glazing

Windscreen and front-side values are estimates; rear and roof values are measured on film-on-glass. Replace with your own data.

Set Kriya SHGC per window. A Kriya VLT ≥ 70 % is required for the windscreen and front side windows (UN R43); rows missing the required entries are excluded from the chain.

WindowTreatedArea (m²)Ref SHGCKriya SHGCKriya VLTState
WindscreenR43: VLT ≥ 70 %
%
in chain
Side front (L+R)R43: VLT ≥ 70 %
%
in chain
Side rear (L+R)—in chain
Rear window (backlight)—in chain
Roof (panoramic)—in chain

Reference glazing default is the measured no-ATO point of the 2018 PVB pilot series (SHGC 0.89, EDTM WP4500). The windscreen and front-side Kriya SHGC of 0.50 at VLT 70 % is extrapolated from the 2020 laminate run (SHGC 0.46–0.48 at VLT 66–68 %) using the ≈ 0.01 SHGC per % VLT slope of the measured Kriya series. Rear sides, rear window and roof default to Kriya SHGC 0.24 at VLT 28 %, the lowest point of the kriya-film-on-glass measurement series (no R43 VLT floor behind the B-pillar). Roof area default is an example — enter your own.

Heat through the glazing

Values are W/m² of solar heat entering each pane (G × SHGC). Fills come from a single sequential scale; numbers are printed on each pane so colour is not the only cue.

Current glazing

Top view of a passenger car with per-pane solar heat values in W/m². windscreen: 534 W/m²; front side: 534 W/m²; rear side: 534 W/m²; rear window: 534 W/m²; roof: 534 W/m².Front534534W/m²534

Front side 534 · Rear side 534 W/m²

With Kriya glazing

Top view of a passenger car with per-pane solar heat values in W/m². windscreen: 300 W/m²; front side: 300 W/m²; rear side: 144 W/m²; rear window: 144 W/m²; roof: 144 W/m².Front300144W/m²144

Front side 300 · Rear side 144 W/m²

Total solar heat through the glazing (Σ A · G · SHGC):2643 W → 1001 W−62.1 %
StepValueSource / formula
1. Optics5 window(s) in chainISO 13837 TTS per entry (or handheld-spectrometer fallback)
2. Solar heat1.64 kWΔQ_solar = Σ A · G · ΔTTS
3. Cooling load1.64 kWSteady-state: ΔQ_cool = ΔQ_solar
4. Compressor821.0 WΔP_compressor = ΔQ_cool / COP
5b. ICE fuel/km0.466 L/100kmΔV_fuel/km = (ΔP/η_eng [/η_alt] · 3600 / v_avg) / LHV
5b. Peak ΔCO₂10.86 g/kmΔ g CO₂/km = ΔV_fuel × CO₂/L (CO₂/L per Impl. Reg. (EU) 2023/2767 annex)
6. Annual ΔCO₂1.846 g/kmPeak · UF. Peak: Δ g CO₂/km = ΔV_fuel × CO₂/L (CO₂/L per Impl. Reg. (EU) 2023/2767 annex). UF: UF (real-world MAC usage factor) per JRC140166 §2.2.8 (regulatory anchor under Reg. (EU) 2023/2767).

What could this mean for an OEM fleet?

All four cards derive from the chain's single unrounded annual Δ CO₂/km. Pick a manufacturer group or brand; model year sets the eco-innovation ceiling (7 → 6 → 4 g/km at 2025 and 2030) and projects the brand's distance to target against the EU fleet target schedule (93.6 g/km held through 2029, then 49.5 g/km from 2030). The projection holds brand emissions constant at 2025 levels and lets only the target move.

Registrations, distance to target and (unless overridden) BEV share are held at the 2025 snapshot from data/oem-fleet-2025.json. Only the eco-innovation ceiling changes with the model year (7 → 6 → 4 g/km at 2025 and 2030); the EU fleet-target projection also widens the gap at 2030. Change the BEV share above to model a higher electric share — the number of ICE+PHEV cars carrying the saving follows it.

Annual Δ from the chain: 1.846 g/km

Annual saving — Mercedes-Benz

Range from the chain: low uses the current treated set without the roof; high adds the roof at the entered roof area. High stays empty until a roof area is entered.

MetricLow (no roof)High (+ roof)
CO₂ saved per year on the roadFleet × annual mileage 15,000 km6,846 t13,041 t
Fuel saved per yearChain fuel/km × annual mileage × fleet2,938,194 L5,597,193 L
Lifetime CO₂ for one year of registrationsFleet × lifetime mileage 200,000 km91,280 t173,886 t
Penalty-equivalent valueIf credited as an eco-innovation€43.4 M€82.6 M

Each euro figure uses the €95/g/km excess-emissions premium from Reg. (EU) 2019/631 Art. 8(1), passed through the Art. 7(3) 0.5 g/km gate. Below the floor the "credited" value is €0 and "if credited" shows the ungated amount.

A — Real-world CO₂ reduction

Fleet tonnes/year if the glazing saved 1.846 g/km on each ICE + PHEV car over 15,000 km/yr. Not credited today — WLTP runs the AC off.

13,041 t
N = 470,937 ICE + PHEV cars (Mercedes-Benz)

B — Approved eco-innovation (today's rules)

Stand-alone penalty avoided if solar-control glazing were approved under Reg. (EU) 2023/2767. Capped at the year-2025 ceiling (6 g/km) and the brand's distance to target.

€82.6 M
Headroom: 5.8 g/km · Gap: 17 g/km
Floor crossing at COP ≈ 7.38 (outside the COP slider range).
Floor crossing when the current glazing reads SHGC ≥ 0.49.

C — Assumed future rules

Scenario only, not current law — if the AC benefit were counted under a hypothetical MACTP-style rule with no cap.

€82.6 M
Gap-bounded only (no eco-innovation ceiling)

D — Value per car (OEM-independent)

Penalty-equivalent value per combustion/PHEV car at today's €95/g/km premium. Capped at €570.00/car for 2025.

€175.39/car

Compliance is assessed per pool and on the 3-year average. BEVs carry no €95/g/km penalty (treated as 0 g/km under Reg. (EU) 2019/631 Art. 8).

Methodology: Model 887 derived from peer-reviewed thermal models

The calculator does not invent a new physics model. It composes three published methodologies into a single per-platform output:

  1. Cabin heat balance — NREL and SAE thermal-load methodology (Rugh et al., NREL/CP-540-37077 and successors) for steady-state cabin temperature under defined solar load.
  2. Solar load reference — ISO 15469-3 reference solar irradiance (1000 W/m2 perpendicular at AM1.5) for the heat-input boundary condition.
  3. AC power conversion — ASHRAE 1991 cooling-load to compressor-electrical-power factor, applied to a representative automotive AC system COP of 1.8 to 2.4.

Validation conditions: 35 degrees Celsius ambient, 30 percent relative humidity, full direct solar on horizontal and vertical glazing, target cabin temperature 23 degrees Celsius, occupancy of two adults.

Range impact for premium vs compact EV segments

The thermal-load benefit scales with glazing area, while the range conversion scales inversely with vehicle-specific energy consumption. Larger premium platforms have more glazing but also higher overall energy use; compact platforms have less glazing but each kilowatt-hour saved buys more kilometres. The net effect for solar heat control glazing on representative EVs:

SegmentBattery (kWh)WLTP range (km)AC savingBattery savingRange extension (km)
Compact EV39.3227~30%4.6%7
Mid-size EV62.5335~33%6.6%11
Premium EV85.6442~35%8.5%16

Hot-climate driving: 35 degrees Celsius ambient, sustained solar load. Range extension is the kilometre delta versus baseline clear laminate at equivalent comfort setpoint. See EV range extension for application detail.

How ATO solar heat control coatings reduce SHGC

ATO nanoparticles have a localised surface plasmon resonance tuned by carrier concentration. Kriya's bottom-up sol-gel synthesis produces monodisperse particles in the 10-25 nm range, well below the visible-light scattering threshold, with tight control over antimony doping level (typically 8-12 atomic percent). The resulting dispersion delivers strong NIR absorption with negligible haze contribution and full visible transparency.

Two coating pathways are production-validated:

  • PVB-laminate interlayer — ATO dispersion incorporated into the PVB film during extrusion or via secondary lamination. Full glazing area is treated; encapsulation in glass laminate protects the coating mechanically.
  • UV-curable resin on glass — Kriya-formulated hard coat with embedded ATO, applied by flow coating or slot-die, cured under UV-LED. Suitable for non-laminated glazing or after-laminate treatment.

Both pathways are 100 percent wet-chemistry — no vacuum process, no plasma deposition. This matters at scale: roll-to-roll PVB lines and inline flow-coating lines run at production speeds that vacuum processes cannot match, and they do not require capex on chamber infrastructure.

Eco-innovation credit pathway (EU Regulation 2019/631)

For European OEMs, the cabin energy saving has a regulatory dimension beyond range. Articles 11 and 12 of Regulation (EU) 2019/631 allow manufacturers to claim CO2 credits for technologies whose benefit is not captured by WLTP. WLTP runs at controlled lab temperature without solar load, so the AC-saving benefit is invisible to type approval.

The combined eco-innovation ceiling is 6 g CO2/km per manufacturer per year for 2025–2029 (Regulation (EU) 2023/851, amending Reg. (EU) 2019/631 Art. 11(1); 7 g/km until 2024, 4 g/km from 2030). At 95 EUR per g/km per vehicle in fleet penalty terms, a 1 g/km credit applied across 800,000 EU registrations is worth 76 million EUR of avoided penalty exposure annually.

For the full credit pathway — methodology submission, independent verifier validation, Commission Implementing Decision, and per-platform application — see the EU CO2 fleet penalty and glazing eco-credit brief. For the fleet exposure model, see EU CO2 penalty impact.

Model limitations — what this calculator does not do

Calculation Model 887 is thermal-only. Honest scope: it does not simulate aerodynamic drag, rolling resistance, regenerative braking recovery, battery thermal management at low state-of-charge, HVAC blower fan power, or driver-behaviour variability. It assumes a clean steady-state cabin-balance condition under defined solar load and a fixed AC system coefficient of performance.

For end-to-end energy-balance simulation under real-world driving cycles, the calculator output is an input — the AC energy saving in kWh per 100 km or watts continuous — to a full vehicle dynamics model (GT-SUITE, AVL Cruise, Simulink Powertrain). For homologation-grade methodology under Commission Implementing Regulation (EU) 2023/2767, Kriya produces a platform-specific dossier with verifier sign-off.

Frequently asked questions

What does this automotive solar heat gain calculator actually compute?

For a chosen EV segment (compact, mid-size, premium), the calculator estimates the cabin temperature reduction under reference solar load, the AC compressor power saving at equivalent comfort setpoint, the resulting range extension in kilometres, and the energy cost saving in five currencies. The thermal model is based on standard solar heat gain coefficient (SHGC) methodology applied across the full glazing area of representative production vehicles.

How is solar heat gain coefficient (SHGC) defined for automotive glazing?

SHGC is the fraction of incident solar radiation that becomes heat inside the cabin — both directly transmitted and absorbed-then-reradiated inward. A clear automotive laminate sits around 0.55-0.65 SHGC; ATO-coated solar heat control laminates can reduce this to 0.35-0.45 by absorbing near-infrared (NIR) wavelengths between 780-2500 nm. The calculator uses the delta between baseline and treated SHGC as its primary input.

Why does AC load matter so much for EV range?

Air conditioning is the single largest non-traction load on a BEV. Under hot-climate driving (35 degrees Celsius ambient, full solar load), AC can draw 2-4 kW continuously, which on a 200-Wh/km vehicle equates to 10-20 percent of total energy use. Reducing AC duty cycle by 30-40 percent — the range observed with ATO solar heat control glazing — translates directly to measurable range extension under the same conditions.

What thermal model underlies Calculation Model 887?

The model derives from peer-reviewed vehicle thermal analyses (NREL/SAE methodology for cabin heat balance, ISO 15469 solar load reference, ASHRAE 1991 air-conditioning power conversion). Inputs include glazing area per platform, reference solar irradiance (1000 W/m2 perpendicular), ambient and target cabin temperature delta, SHGC reduction from coating, and battery-specific energy. Outputs are deterministic — no Monte Carlo simulation — and rounded for engineering use.

Does this calculator account for aerodynamic and rolling-resistance losses?

No. Calculation Model 887 is a thermal-only model. It quantifies the AC-load reduction and converts that to range extension at constant powertrain efficiency. It does not model wind drag, rolling resistance, regen recovery, or HVAC blower power. For an end-to-end energy-balance simulation, the calculator output should be paired with a full vehicle dynamics model.

How does this map to the EU eco-innovation credit?

AC-load reduction via solar heat control glazing falls under the eco-innovation framework of Regulation (EU) 2019/631, Articles 11 and 12. The CO2 saving per vehicle is computed by converting the AC energy delta via grid CO2 intensity for BEVs, or vehicle-specific fuel-to-CO2 factors for ICE. See the regulatory brief linked below for the credit pathway, ceiling, and approval timeline.

Can the numbers be customised for a specific OEM platform?

Yes. The on-page calculator uses three pre-loaded segment archetypes. For a per-platform run with actual glazing surface area, climate-zone solar load assumptions, battery and powertrain efficiency, and the manufacturer-specific WLTP-to-real-world correction factor, Kriya engineering produces a bespoke methodology dossier. Contact engineering to scope a platform-specific calculation.

Need a platform-specific calculation?

The on-page tool runs three segment archetypes. For a per-vehicle dossier with your glazing area, climate zone, and powertrain efficiency, contact engineering.

Talk to engineering